Outland XT: Replacing the Mid-Drive MotorUpdated 5 hours ago
This guide shows how to remove the mid-drive motor from an Outland XT and fit a replacement. It is written for a bike shop or an experienced home mechanic. The motor is removed and fitted as a sealed unit: never open the motor casing.
Before you start: please contact us through our Warranty Claim page first. We'll confirm whether the motor needs replacing, supply the correct replacement motor and its bolt torque values, and confirm in writing who will do the work. Third-party repairs done without our prior written confirmation aren't reimbursed.
When the motor needs replacing
On the Outland XT, the crank bolts screw into a spindle that is part of the motor. If a crank arm is loose or a crank bolt won't tighten, check where the damaged thread is:
- Thread in the crank arm damaged: replace the crank arm only. The motor stays.
- Thread inside the motor spindle damaged: the spindle can't be replaced on its own, so the whole motor is replaced.
Please stop riding the bike until it is repaired. A loose crank can come off while riding.
What you'll need
- The replacement motor supplied by Ridewave. Check that its model label matches the old motor.
- Metric hex keys, Torx keys and a socket set
- A crank puller to suit the crank arms
- A chainring lockring tool to suit the chainring
- A torque wrench
- Medium-strength (blue) threadlocker and bike grease
- A phone camera, cable ties and masking tape for labelling plugs
- A bike stand or a helper to hold the bike steady
Step 1: Make the bike safe
- Turn the bike off and remove the battery.
- Press the power button once with the battery out, to discharge the system.
- Put the bike in a stand or lay it on a clean, soft surface, drive side up.
Step 2: Remove the cranks and chainring
- Remove the chain guide, if fitted, and lift the chain off the chainring. Let it hang out of the way.
- Remove the crank bolt on each side, then pull each crank arm off with the crank puller. Screw the puller fully into the arm before you turn the inner bolt, so you don't strip the arm's thread.
- Remove the chainring lockring with the lockring tool, then slide the chainring off.
- Remove any motor cover or bash guard under the motor.
Step 3: Unplug the motor
- Take clear photos of every cable and plug at the motor before you touch them.
- Label each plug with masking tape.
- Unplug the motor connectors: the main cable harness (display, brake cut-off and throttle) and the speed sensor cable. Pull on the plug, never the wire.
Step 4: Remove the motor
- Support the motor with one hand or have a helper hold it. It is heavy.
- Remove the motor mounting bolts. Take out the side bolts first and the centre bolt last.
- If a bolt is tight, twist and pull it out. Don't hammer it.
- Gently wiggle the motor down and out of the frame mounts, keeping the cables clear.
Step 5: Fit the replacement motor
- Clean the frame mounts and the bolt holes.
- Lift the new motor into place, guiding the cables so nothing is pinched between the motor and the frame.
- Put a little blue threadlocker on each mounting bolt and start every bolt by hand.
- Check the motor sits flat against the frame mounts, then tighten the bolts in a cross pattern to the torque values supplied with the motor.
- Reconnect each plug to match your photos and labels until it seats fully. Tidy the cables with cable ties.
- Refit the motor cover or bash guard.
Step 6: Refit the chainring and cranks
- Slide the chainring on and tighten the lockring with the lockring tool.
- Lightly grease the spindle ends, fit both crank arms opposite each other and tighten the crank bolts to the torque values supplied with the motor.
- Refit the chain and the chain guide.
Step 7: Check before riding
- Fit the battery and turn the bike on. The display should start normally with no error code.
- With the rear wheel off the ground, turn the cranks and check the assist starts smoothly in each pedal-assist level.
- Squeeze each brake lever while the assist is running. The motor should stop straight away.
- Check the start-up throttle, which assists up to 6 km/h only.
- Listen for grinding or clicking, and check the cranks have no side-to-side play.
- Take a short, slow test ride in a quiet area, then recheck the motor mounting bolts and crank bolts.
If an error code shows, the assist doesn't work or you hear a new noise, stop and contact us before riding further.
Need help?
- Submit a warranty claim or repair request with your order number, a photo of the motor label and photos or a video of the problem.
- Contact Ridewave
- Phone: 0468 095 888
- Email: [email protected]